BS ISO 14300-2 pdf download
BS ISO 14300-2 pdf download Space systems — Programme management Part 2: Product assurance 1 Scope This part of lSO 14300 defines the product assurance (PA) policy, objectives, principles, and requirements forthe establishment and implementation of PA programmes for space programmes covering mission definition,design, development, production and operations of space products, including disposal. The PA discipline covers: PA management,quality assurance，safety...
BS ISO 14793 pdf download
BS ISO 14793 pdf download Road vehicles — Heavy commercial vehicles and buses — Lateral transient response test methods 1 Scope This International Standard specifies test methods for determining the transient response behaviour of heavycommercial vehicles， heavy commercial vehicle combinations, buses and articulated buses,as defined inISO 3833 for trucks and trailers above 3,5 t and buses above 5 t maximum...
BS ISO 15765-1 pdf download
BS ISO 15765-1 pdf download Road vehicles — Diagnostic communication over Controller Area Network (DoCAN) Part 1: General information and use case definition 4 Conventions ISO 15765 is based on the conventions discussed in the Osl Service Conventions (ISO/IEC 10731) as theyapply for diagnostic services. 5 Overview of lSO 15765 5.1General ISO 15765 is applicable to vehicle diagnostic systems implemented...
BS ISO 16000-3 pdf download
BS ISO 16000-3 pdf download Indoor air Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air — Active sampling method 1 Scope This part of ISO 16000 specifies a determination of formaldehyde (HCHO) and other carbonyl compounds (aldehydes and ketones) 1 in air. The method is specific to formaldehyde but, with modification, at...
BS ISO 17214 pdf download
BS ISO 17214 pdf download Space data and information transfer systems — Spacecraft onboard interface services — Time access service 1 Scope This International Standard defines services and service interfaces provided by the Spacecraft OnboardInterface Services (SoIS) time access service. It specifies only the service and not the methods of providingthe service, although use of the soIS subnetwork services is...
BS ISO 17359 pdf download
BS ISO 17359 pdf download Condition monitoring and diagnostics of machines — General guidelines 1 Scope This International Standard sets out guidelines for the general procedures to be considered when setting up acondition monitoring programme for machines and includes references to associated standards required inthis process.This lnternational Standard applies to all machines. 2Normative references The following referenced documents are indispensable...
BS ISO 18132-3 pdf download
BS ISO 18132-3 pdf download Refrigerated hydrocarbon and non-petroleum based liquefied gaseous fuels — General requirements for automatic tank gauges Part 3: Automatic tank gauges for liquefied petroleum and chemical gases on board marine carriers and floating storage 1 Scope This part of lSO 18132 establishes general principles for the accuracy, installation, calibration and verificationof automatic tank gauges (ATGs) used...
BS ISO 19706 pdf download
BS ISO 19706 pdf download Guidelines for assessing the fire threat to people 1 Scope This International Standard is intended to serve as general guidelines for the assessment of the fire threat to people. It encompasses the development, evaluation and use of relevant quantitative information for use in fire hazard and risk assessment. This information, generally obtained from fire-incidence investigation,...
BS ISO 19892 pdf download
BS ISO 19892 pdf download Plastics piping systems — Thermoplastics pipes and fittings for hot and cold water — Test method for the resistance of joints to pressure cycling 1 Scope This International Standard specifies a method for testing the resistance of joints to pressure cycling. ltis applicable to piping systems based on thermoplastics pipes intended to be used in...
BS ISO 19893 pdf download
BS ISO 19893 pdf download Plastics piping systems — Thermoplastics pipes and fittings for hot and cold water — Test method for the resistance of mounted assemblies to temperature cycling 1 Scope This International Standard specifies a method for testing the resistance to temperature cycling of joints for piping systems with rigid or flexible thermoplastics pipes. It is applicable to...