ASME MFC-7 pdf download
ASME MFC-7 pdf download Measurement of Gas Flow by Means of Critical Flow Venturis and Critical Flow Nozzles SCOPE AND FIELD OF APPLICATION This Standard applies only to the steady flow of single-phase gases through critical flow venturis (CFV) of shapesspecified herein also sometimes referred to as critical flow nozzles (CFN), sonic nozzles, or critical flow venturinozzles). This Standard applies...
ASME MFC-10M pdf download
ASME MFC-10M pdf download METHOD FOR ESTABLISHING INSTALLATION EFFECTS ON FLOWMETERS (c) The tests outlined in this Standard should cover the pertinent range of fluid flow rates, Reynolds num- bers, etc., of the meter to be evaluated. NOTE: This requirement can be satisfied by stating the range of pertinent nondimensionalized parameters over which the data were obtained (see Section 7)....
ASME MFC-12M pdf download
ASME MFC-12M pdf download Measurement of Fluid Flow in Closed Conduits Using Multiport Averaging Pitot Primary Elements 4 OPERATING PRINCIPLES 4.1 Description of Operation The multiport averaging Pitot primary flow element or averaging Pitot tube (APT) is similar to the conven- tional single point Pitot tube in operation, but differs in construction. It is typically designed as a strut, or...
ASME MFC-11 pdf download
ASME MFC-11 pdf download Measurement of Fluid Flow by Means of Coriolis Mass Flowmeters Repeatability, expressed as a percentage of the reading, may also be a separate parameter.Accuracy and repeatability statements are usuallymade at reference conditions that are specified by themanufacturer.These reference conditions shouldinclude temperature, humidity, pressure, fluid densityand flow range. 3.3 Factors Affecting Mass Flow Measurement 3.3.1 Density and...
ASME MFC-16 pdf download
ASME MFC-16 pdf download Measurement of Liquid Flow in Closed Conduits With Electromagnetic Flowmeters SCOPE1 This Standard is applicable to industrial electromagnetic flowmeters and their application in the measurement of liquid flow. The electromagnetic flowmeterscovered by this Standard utilize an alternating electricalcurrent (AC) or pulsed direct-current (pulsed-DC) togenerate a magnetic field in electrically conductive andelectrically-homogeneous liquids or slurries flowing ina...
ASME MFC-21.1 pdf download
ASME MFC-21.1 pdf download Measurement of Gas Flow by Means of Capillary Tube Thermal Mass Flowmeters and Mass Flow Controllers SCOPE This Standard establishes common terminology andprovides guidelines for the quality, description, principle of operation, selection, operation, installation, andflow calibration of capillary tube thermal mass flow-meters and mass flow controllers for the measurementand control of the mass flow rate of...
ASME MFC-22 pdf download
ASME MFC-22 pdf download Measurement of Liquid by Turbine Flowmeters 6.3 Piping 6.3.1 Turbine meters are normally installed in a horizontal orientation. The manufacturer should be con- sulted if space limitations dictate a different orientation for the meter. 6.3.2 Where the flow range is over the limit of any one meter or the prover for the system, a bank of...
ASME N51 pdf download
ASME N51 pdf download In-Service Testing of Nuclear Air-Treatment, Heating, Ventilating, and Air-Conditioning Systems 3.3.2 System Operating Conditions. Operating con- ditions required for in-service testing shall be deter- mined for each system. 3.3.3 Procedure Requirements. The owner shall be responsible for the development and implementation of written test procedures that meet the requirements of this Standard. Each equipment test section...
ASME N510 pdf download
ASME N510 pdf download Testing of Nuclear Air Treatment Systems test boundary: the physical limit component, system, ordevice being subjected to a leakage test as defined inspecific procedures. test canister: a specially designed sample holder con-taining sufficient adsorbent for specific laboratory teststhat can be removed from an adsorber bank, withoutdisturbing the remainder of the adsorber, to providerepresentative samples for laboratory...
ASME N511 pdf download
ASME N511 pdf download In-Service Testing of Nuclear Air Treatment, Heating, Ventilating, and Air-Conditioning Systems 3.3.1 Inspection and Test Parameters. Parameters that need to be observed, calculated, and recorded in order to meet the requirements of this Standard shall be identified for each system. 3.3.2 System Operating Conditions. Operating con- ditions required for in-service testing shall be deter- mined for...