ASME BPVC 2192-3 pdf download
ASME BPVC 2192-3 pdf download Case 2192-3 Modified 9Cr-1Mo-V Cast Material Section I Inquiry: May normalized and tempered modified 9Cr-1Mo-v castings, and with the chemical analysis shownin Table 1,the mechanical properties shown in Table2 , and otherwise conforming to applicable requirementsin the following specifications,be used for Section Iconstruction? (a) Castings，SA-217(b) Pipe，SA-426 Reply: It is the opinion of the Committee that...
ASME BPVC 2239-1 pdf download
ASME BPVC 2239-1 pdf download Case 2239-1 Use of Permanent Mold Cast Aluminum Alloys UNS A13560 and A03570 Section VIII, Division 1 Inquiry: May aluminum alloys UNS A13560 and A03570 in the overaged temper meeting the chemical composition and mechanical properties given in Tables 1 and 2 and other requirements of SB-108 be used in Section VIII, Division 1 construction?...
ASME BPVC 2344 pdf download
ASME BPVC 2344 pdf download Case 2344 Use of Sand Cast Aluminum Alloy A356.0, T6 Temper, for the Manufacture of Hot Water Heating Boilers Under Part HC Section IV lnquiry: May aluminum alloy A356.0 sand castings inthe T6 temper meeting the chemical composition andmechanical properties given in Tables 1 and 2 andother requirements of ASTM B 26/B 26M-97 be usedin...
ASME MFC-8M pdf download
ASME MFC-8M pdf download FLUID FLOW IN CLOSED CONDUITS: CONNECTIONS FOR PRESSURE SIGNAL TRANSMISSIONS BETWEEN PRIMARY AND SECONDARY DEVICES The detail design for the installation of the flowmeter secondary system should consider instrument trouble- shooting and calibration. Access to the impulse lines, the valves, manifold and the secondary device is required. Installations providing this access must not compromise the measurement...
ASME N509 pdf download
ASME N509 pdf download NUCLEAR POWERPLANT AIR-CLEANING UNITS AND COMPONENTS 1 SCOPE This Standard covers requirements for the design, construction, and qualification and acceptance testing of the air-cleaning units and components which make up Engineered Safety Feature (ESF) and other high effi- ciency air and gas treatment systems used in nuclear power plants. 1.1 Limitations The Standard does not cover...
ASME 2 pdf download
ASME 2 pdf download Methods of test for textiles 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility...
ASME PTC2 pdf download
ASME PTC2 pdf download DEFINITIONS AND VALUES 2.1 INTRODUCTION The Codes provide test procedures which yieldresults of the highest level of accuracy consistentwith the best engineering knowledge and practice,taking into account the cost of tests and monetaryvalue of efficiency to industry. Performance of equip-ment is determined in part by measurements ofphysical quantities.A measurement consists of sens-ing a physical variable and...
ASME PTC-50 pdf download
ASME PTC-50 pdf download FUELCELL POWERSYSTEMS PERFORMANCE 1.2 SCOPE This Code applies to all fuel cell power systems regardless of the electrical power output, thermal output, fuel cell type, fuel type, or system application. Fuel cell power systems contain an assembly of electrochemical cells, which oxidize a fuel to gener- ate direct current electricity. Balance-of-plant subsys- tems may include controls,...
ASME QEI-1 pdf download
ASME QEI-1 pdf download Standard for the Qualification of Elevator Inspectors 1.1.1 Inspectors and Inspector Supervisors This Standard includes requirements for the qualifica-tion, duties, and responsibilities of inspectors andinspector supervisors engaged in the inspection andtesting of (a) hoisting and lowering mechanisms, equipped witha car or platform, that move between two or more land-ings.This equipment includes, but is not limited to,...
ASME Y14 pdf download
ASME Y14 pdf download SCREW THREAD REPRESENTATION 1 GENERAL 1.1 Scope This Standard establishes requirements for pictorialrepresentation, specification,and dimensioning of screwthreads on drawings; it is not concerned with standardsfor dimensional control of screw threads. Informationhelpful in the design and selection of screw threadsto meet specific requirements is included in the B1series of the ASME Standards for Screw Threads (seepara. 1.3)....