ASME B89.7.3.1 pdf download
ASME B89.7.3.1 pdf download CUIDELINES FOR DECISION RULES: CONSIDERING MEASUREMENT UNCERTAINTY IN DETERMINING CONFORRIIANtE TO SPECIFICATIONS 3 REQUIREMENTS FOR DECISION RULES 3.1 Zone Identification A decision rule must have a well-documented method of determining the location of the acceptance, rejection, and any transition zones. 3.2 Decision Outcome Each zone of a decision rule must correspond to a documented decision that...
ASME B89.1.13 pdf download
ASME B89.1.13 pdf download MICROMETERS 1 sCOPE This Standard is intended to provide the essentialrequirements for micrometers as a basis for mutualunderstanding between manufacturers and consumers.Outside，inside，and depth micrometers are describedin the Standard. 2 DEFINITIONS backlash:a relative movement between interactingmechanical parts，resulting from looseness [ASMEB5.54M-1992 (R1998)]. In this Standard,backlash isfurther defined as the rotation of the spindle, in theopposite direction of the...
ASME B107.2 pdf download
ASME B107.2 pdf download SOCKETWRENCHES, EXTENSIONS, ADAPTORS, AND UNIVERSALJOINTS, POWERDRIVE(IMPACT) (INCH SERIES) 4.4 Markings Sockets and attachments shall be marked in a plain and permanent manner with the manufacturer’s name or with a trademark of such known character that the source of manufacture and country of origin may be readily determined. In addition, sockets shall be marked in a plain...
ASME B107.11 pdf download
ASME B107.11 pdf download PLIERS: DIAGONAL IUTTINI AND END CUTTINE 5.5.2 Permanent Set. Permanent set of the handles for all types, except Type II, shall not exceed 0.04 in. (1.0 mm) when subjected to the handle load test specified in para. 6.4. Handles contacting each other during load testing shall constitute failure. 5.5.3 Comfort Grips. When comfort grips are furnished...
ASME B107.15 pdf download
ASME B107.15 pdf download FLAT TIP SCREWDRIVERS 5.4.2 Finish. The blade shall be treated in a manner to resist rust or corrosion. There shall be no evidence of peeling or chipping of any coating where applicable. 5.4.3 Hardness. The tip portion of the screwdrivers or the entire blade shall be hardened to not less than 48 HRC (para. 6.2). 5.4.4...
ASME B107.24 pdf download
ASME B107.24 pdf download LOCKING PLIERS 4.2 Material Materials used in the manufacturing of the pliers shallbe such as to produce pliers conforming to the require-ments hereinafter specified. 4.3 Design Pliers shall be similar to the figure to which referenceis made and shall be proportioned in all parts so as to meet the requirements of this Standard. Pliers shall be-provided...
ASME B107.36 pdf download
ASME B107.36 pdf download ASME STANDARDS COMMITTEE B107 Hand Tools and Accessories 4.4Handles Handles of plicrs shali be through hardenedfrom30 to 50 HRC or case hardened fron 75 to 86 HR15N,with a case dcpth of a ninimun of 0.010 in. (0.25mm). Handles shall be so shaped as to afford a confort-able grip and shall be free from rough edges and...
ASME B107.54 pdf download
ASME B107.54 pdf download HEAVY STRIKING TOOLS: SAFETY REQUIREMENTS 1 GENERAL 1.1 Scope This Standard provides safety requirements for the design, construction, testing, and use of the following styles of heavy striking tools. The names given and intended uses are those generally recognized (see Fig. 1). (a) Blacksmith’s Double-Face Sledges. Nevada long- pattern striking hammers, and Oregon short-pattern striking hammers,...
ASME B107.57 pdf download
ASME B107.57 pdf download BRICKLAYERS’ HAMMERS AND PROSPECTING PICKS: SAFETY REQUIREMENTS biade:the tapered portion of ihe trieklaycrs” hammer-head directly opposite the face. chanfer: the angled lat surface r cquivalcnt radiusencircling the perimeler of the face of the bricklayers’hammer and prospccling picks and a1 both ends af thecutting edge of the bneklaycrs” harnmer.cheeks:see sides. curring edge rbit): the edge directly opposite...
ASME B107.100 pdf download
ASME B107.100 pdf download MpENOucQlVhtluito INCORPURATING ASME B107.B,ASME B107.9,ASME B107.39, ASME B107.40 4.5 Proof Torque When tested as specified, wrenches shall withstand the proof torque specified in the applicable tables without failure or permanent deformation (set), which might affect the durability or serviceability of the wrenches. Proof torque is a predetermined test torque to which a sample is subjected before...