ASME A112.19.13 pdf download
ASME A112.19.13 pdf download ELECTROHYDRAULIC WATER CLOSETS 1 GENERAL 1.1 Scope This Standard establishes performance, electrical/elec-tronic conformance,temperature，life cycle，marking,and identification requirements for electrohydraulicwater closets. The use of alternate materials or methods are permit-ted, provided the proposed material or method complieswith the performance requirements and intent of thisStandard. 1.2 Units of Measurement Values are stated in U.s. Customary units and theInternational System...
ASME A120.1 pdf download
ASME A120.1 pdf download Safety Requirements for Powered Platforms and Traveling Ladders and Gantries for Building Maintenance 1.3 Application of This Standard 1.3.1 ð21Þ Applications. This Standard applies to the instal- lation ofall powered platforms and traveling ladders and gantries. Permanentpowered platforms shall be provided on all buildings with vertical platform travel exceeding 300 ft (91 m). 1.3.2 Deviations. Deviations...
ASME A16.22 pdf download
ASME A16.22 pdf download WROUGHT COPPER AND COPPER ALLOY SOLDER JOINT PRESSURE FITTINGS No.C23000，for which allowable stresses are foundin ASME B31.1，ASME B31.9,or ASME Boiler andPressure Vessel Code，Section l —Materials. (b) Other coppers and copper alloys are permitted,provided they meet the chemical requirements of 84%minimum copper and 16% maximum zinc, and providedthe fittings produced from the copper alloy meet allthe mechanical...
ASME B1.13M pdf download
ASME B1.13M pdf download METRIC SCREW THREADS: M PROFILE 1GENERAL1.1 Scope This Standard contains general metric standards fora 60 deg symmetrical screw thread with a basic ISo68-1 profile designated M profile.The M profile threadsof tolerance class 6H/6g are intended for metric applica-tions where inch class 2A/2B have been used. At theminimum material limits, the 6H/6g results in a looserfit than...
ASME B1.30 pdf download
ASME B1.30 pdf download SCREW STANDARD THREADS: PRACT1 I: E FOR CALCULATING AI D ROUNDIN[E DIMENSIONS 1 GENERAL 1.1 Purpose The purpose of this Standard is to establish uniform and specific practices for calculating and rounding the numeric values used for inch and metric screw thread design data dimensions only. No attempt is made to establish a policy of rounding...
ASME A15.8 pdf download
ASME A15.8 pdf download CHUCKS AND CHUCK JAWS 9 SPECIFICATIONS OF CHUCKS FOR USA STANDARD SPINDLE NOSES 9.1 Specifications of Chucks for Type A and Type B Spindle Noses Chucks for Type A and Type B spindle noses shall have the mounting made to the dimensions of Table 4 of ANSI B5.9-1967. 9.2 Specifications of Chucks for Type D-I Spindle...
ASME B5.60 pdf download
ASME B5.60 pdf download WORKHOLDING CHUCKS: JAW TYPE CHUCKS Incorporating ASME B5.60.1 and ASME B5.60.4 1 INTRODuCTION This American National Standard establishes techni-cal requirements for workholding chucks used primarilyin turning operations.It covers jaw type chucks whethermanual or power-operated. 2 sCOPE This Part of the ASME B5.60 standard covers theGeneral Description and Definitions of Terms relatedto jaw type workholding chucks. 3...
ASME B5-8 pdf download
ASME B5-8 pdf download CHUCKS AND CHUCK JAWS 1 SCOPE AND PURPOSE This Standard applies to chucks for use on engine lathes, tool room lathes, turret lathes, and automatic lathes and fit American Standard Spindle Noses of ANSI-B5.9-1967. They may be used on other applica- tions for which they are suitable (see pages 4 and 5 of ANSI-B5.9-1967). It is...
ASME B16.9 pdf download
ASME B16.9 pdf download FACTORY-PA ADE WROUGHT BUTTWELDINC FITTINGS 1 scOPE1.1 General This Standard covers overall dimensions，tolerances,ratings,testing, and markings for wrought factory-madebuttwelding fittings in sizes NPs through 48 (DN15 through 1200). 1.2 Special Fittings Fittings may be made to special dimensions，sizes,shapes, and tolerances by agreement between the manu-facturer and the purchaser. 1.3 Fabricated Fittings Fabricated laterals and other fittings employing...
ASME A16.18 pdf download
ASME A16.18 pdf download CAST COPPER ALLOY SOLDER JOINT PRESSURE FITTINGS 4 SIZE The size of the fittings shown in Table 3 and Table A1 corresponds to standard water tube size as shown in ASTM B 88, Specification for Seamless Copper Water Tube. The size of the threaded ends corresponds to nominal pipe size as shown in ASME B1.20.1. Fittings...