ASME 3287 pdf download
ASME 3287 pdf download NDUSTRIALJCKS: SYMBOLS FOR CONTROLS AND OTHER DISPLAYS 1 scoPE This Standard establishes symbols for use on operatorconirols and oier displays on powered industria trucks. 2 NORMATiIVE REFERENCES The following normative docurnents contain provi-sions which，through reference in this iext，constituteprovisions of this Standard. For dated references,subse-quent amendments to,or revisions of，any of thcsepublications do not apply. However，partics toagreements based...
ASME A112.6.7 pdf download
ASME A112.6.7 pdf download ENAMELED AND EPOXY COATED CAST IRON AND PVC PLASTIC SANITARY FLOOR SINKS 2.2 Epoxy Coating The visible surface after installation of each floor sink shall be acid-resisting epoxy, thoroughly fused to the cast iron base. It shall be free from flaws that may effect the appearance or serviceability of the floor sink. The epoxy surface shall...
ASME A112.14.4 pdf download
ASME A112.14.4 pdf download GREASE REMOVAL DEVICES 1.4 Definition automatic grease/oil removal device (GRD): a plumb- ing appliance that is installed in the sanitary drainage system in order to intercept free-floating fats, oils, and grease from waste water discharges. Such equipment operates on a time- or event-controlled basis and has the ability to remove the entire range of commonly available...
ASME A112.18.3 pdf download
ASME A112.18.3 pdf download PERFORMANCEREQUIREMENTS FORBACKFLOWPROTECTION DEVICES AND SYSTEMS IN PLUMBING FIXTUREFITTINGS 6 GENERAL REQUIREMENTS FOR BACKFLOW PREVENTION DEVICES 6.1 Functional Backflow prevention devices shall be designed to pre- vent pollution and contamination of the potable water system. 6.2 Materials Materials in contact with potable water shall comply with the requirements of ASME A112.18.1M. 6.3 Environment 6.3.1 WorkingPressure. Backflow prevention...
ASME A112.19.3 pdf download
ASME A112.19.3 pdf download Stainless steel plumbing fixtures 1 Scope 1.1 This Standard covers plumbing fixtures made of stainless steel alloys and specifies requirements for materials, construction, performance, testing, and markings. Note: The term “corrosion-resisting steel” is also applied to stainless steel. ∆ 1.2 This Standard covers the following plumbing fixtures: a) bathtubs; b) bidets; c) drinking fountains and water...
ASME A112.19 pdf download
ASME A112.19 pdf download ELECTROHYDRAULIC WATER CLOSETS 2.4 Pump Housing Electric motors or pump enclosures shall complywith UL 746C and be plastic rated 94-5V or better asspecified in UL 746C. 2.5 Jet Hose The pump jet hose,if provided，shall withstand apressure of 25 ± 1 psi (172 ± 6.9 kPa) for 60 min. 2.6 Printed Wiring Boards Wiring boards shall comply...
ASME A112.19.14 pdf download
ASME A112.19.14 pdf download Six-Liter Water Closets Equipped With a Dual Flushing Device (c) 0.34 oz (10 mL) of this solution shall be removed from the bowl and shall be added to 5.75 oz (170 mL) of clean water in a suitable container (i.e., dilution ratio of 17:1). A sample of this solution shall be set aside in a test...
ASME A112.19.15 pdf download
ASME A112.19.15 pdf download BATHTUB /WHIRLPOOL BAHTUBS WITH PRESSURE8E ALED DOORS 1.1 Scope This Standard cstablishcs matcrial,mechanical, elec-trical，marking,and testing requirements for bathtubslwhirlpool bathtubs with doors that are made water tightby the use of a pressure seal. It addresses the functionalperformance and physical characteristics for a pressuresealed door of a bathtub/whirlpool bathtub. The door is intended to aiiow for entry into...
ASME A112.19.17 pdf download
ASME A112.19.17 pdf download MAMUFACTURED SAFETY VACUUM RELEASE SYSTEMS (SVRS) FOR RESIDENTIAL AND MMMERCIAl SWIMMINC POO1 POO1 SUCTION SYSTEMS -o35 1GENERAL 1.1 Scope This Standard establishes general requirements,dimensions and tolerances,materials,installationinstructions,testing requirements, and markings andidentification for SvRs devices.svRs devices areintended to be utilized on pool, spa, hot tub, and/ortherapy unit suction systens.SvRs devices coveredunder this Standard are designed to prevent high...
ASME A112.6.3 pdf download
ASME A112.6.3 pdf download FLOOR AND TRENCH DRAINS 4.2 Open Area Requirements for Various Classifications of Drains Opening area requirements for drains shall be as shown in Table 4. 4.3 Openings in Top Grates Openings shall be any geometric shape. Openings shall be sized to exclude debris and accommodate the anticipated traffic. When drainage requirements dictate openings that would permit...